Appendix C2

Apprendix  C(2General Description of the super MINIRES for serial numbers between 100 & 140

 

The MiniRes geophysical resistivity meter is a highly accurate and precise portable scientific instrument designed to provide years of rugged use while maintaining laboratory levels of stability and accuracy. The instrument is also very easy to use. 

 

The MiniRes is not reliant on a digital microprocessor for operation. This has several advantages over typical microprocessor-based systems. A microprocessor-based system generally relies on a menu where the operator has to work his way up or down the menu system to get where he can control the function of interest. In the MiniRes, every function of the instrument corresponds to an individual switch or indicator on the front panel. Therefore, access to a particular function is instantaneous. Another disadvantage of microprocessor-based systems is that they generate electromagnetic noise. Also, they are susceptible to electromagnetic interference (EMI) and electrostatic discharge (ESD). The MiniRes has a slow (but accurate) system clock that generates very little noise. Since it is synchronous with all other functions of the instrument, it does not interfere with the operation of the instrument.

 

A key characteristic of the MiniRes is the receiver architecture. The receiver utilizes a technique called "synchronous detection". This is an extremely powerful theoretical concept that allows stable and accurate readings to be taken in noisy environments with a minimum of transmitter power. Thus, the MiniRes is able to acquire hundreds of measurements with 4 standard "D" cell alkaline batteries as its sole power source.

 

The "synchronous detection" method has the intrinsic ability to filter out vast amounts of noise, allowing stable readings to be taken in extremely noisy environments. Other electronic architectures use a "brute force" method of generating large amounts of transmitter power. This brute force approach is effective, but suffers two disadvantages. First, the brute force method requires large, heavy batteries that lose power with each measurement and, second, the large transmitter currents demand excellent, low resistivity transmitter electrode "plants". Operators of that equipment regularly carry extra water and salt to douse the transmitter electrodes and, thereby, reduce their resistances to the point that the heavy transmitter currents can pass. The MiniRes would require this only in the most extreme of circumstances. 

 

The MiniRes utilizes some of the latest, most sophisticated solid state electronic components available. Many other resistivity meters use mechanical relays for switching the transmitter and receiver circuitry. The MiniRes has no mechanical relays. It utilizes rugged high voltage solid state components for all receiver and transmitter functions. These provide reliable and stable readings year after year.

 

The power supply for the MiniRes consists of four standard alkaline "D" cells hooked in series providing approximately 6 volts. A set of batteries provides hundreds of readings. There is no need for a battery charger. A "BATTERY LOW" indicator light comes on when the batteries get close to needing replacement. Typically, a few hours of data can be taken even after the "BATTERY LOW" LED illuminates. Also, the operation can be further extended if the "RANGE" switch is set to the HIGH (19.999) Ohm position, since the 19.999 Ohm position requires less current and less power.

 

The transmitter circuit of units with serial numbers less than 100 can generate over 400 volts. Those units with serial numbers greater than 100 can generate up to 720 volts, peak-to-peak. This allows the instrument to work in very resistive environments with long transmitter electrode spacing.

 

The frequency of the transmitted signal on units with serial number less than 100 is 30 Hertz and there is excellent rejection of 60 Hertz AC power line noise. On units with serial numbers greater than 100, the frequency is 5 Hertz and there is excellent rejection of both 50 and 60 Hertz AC power noise.

 

Considerable effort was expended in the design of the MiniRes to provide continuous feedback to the operator of every critical function of the instrument. Hence, an "OVERRANGE" detection indicator light assures the operator that the instrument is working properly within its linear bounds. The "BATTERY LOW" indicator provides an early warning for battery replacement. The "LINE OPEN" indicator signals to the operator that the transmitter, transmitter cables or electrodes are not operating properly. All of these quality control indicators assure consistent and robust measurements.                                        30 March 00


Home                Additional Information               MiniRes

 

Comments